|
SPECIFICATIONS |
|
CRT |
| Type |
150mm
rectangular, with internal graticule |
|
Accelerating voltage |
Approx.
12kV |
| Effective
area |
8div.×10div. (1div＝10mm) |
|
Vertical axis (Common for CH1, CH2) |
| Operating
modes |
CH1,
CH2, ADD, ALT, CHOP |
|
Sensitivity |
1mV/div., 2mV/div. : ±5%
5mV/div. to 5V/div. : ±3% |
| Attenuator |
1mV/div.
to 5V/div., 1-2-5 step, (fine adjustment) |
| Input
impedance |
1MΩ±2%,
approx. 25pF |
|
Frequency response |
|
DC |
DC to
50MHz, (－3dB)（5mV/div to 5V/div.）
DC to 20MHz, (－3dB)（1mV/div, 2mV/div.） |
|
AC |
5Hz to
50MHz, (－3dB)（5mV/div to 5V/div.）
5Hz to 20MHz, (－3dB)（1mV/div to 2mV/div.） |
|
Rise time |
Approx.
7ns (5mV/div. to 5v/div.)
Approx. 17.5ns (1mV/div., 2mV/div.) |
|
Crosstalk |
Below
－40dB (at 1kHz) |
|
Polarity inversion |
CH2 only |
|
CHOP Frequency |
Approx.
250kHz |
|
Maximum input voltage |
800Vp-p
or 400V (DC＋AC peak) |
|
Horizontal axis |
|
Operating modes |
Set to
X-Y mode by H MODE
CH1 : Y-axis、CH2 : X-axis |
|
Sensitivity |
Same as
Vertical axis (CH2) |
|
Input impedance |
Same as
Vertical axis (CH2) |
|
Frequency response |
|
DC |
DC to
1MHz, within －3dB |
|
AC |
5Hz to
1MHz, within －3dB |
|
X-Y phase difference |
Below 3
degrees at 50kHz |
|
Maximum input voltage |
Same as
vertical axis (CH2) |
|
Sweep |
| Sweep
modes |
A sweep.
B sweep, ALT |
|
Sweep time |
| A |
0.5s/div
to 0.1µs/div±3% in 1-2-5 steps,21 ranges, and fine adjustment |
| B |
50ms/div
to 0.1µs/div±3% in 1-2-5 steps, 18 ranges |
| Magnified
sweep |
×10±5%
(±8% at 0.5μs/div) |
| Linearity |
±3%
(10MAG ±5%) |
| Delay
method |
Continuous delay, synced delay |
| Delay time |
0.5s/div
to 0.1µs/div ; continuously variable from 0.2div.～10div. |
| Delay time
error |
±(3% of
set value 1% of f.s.) ＋ (0 to 300ns) |
| Delay
jitter |
10,000 :
1 of 10 times of the A sweep time |
| Hold off |
A Sweep
: Continuously variable from NORM |
| Trace
separation |
B
separation from A is continuously adjustable to approx. ±4 div. |
|
Triggering |
| Trigger
sources |
VERT, CH1,
CH2, LINE, EXT |
| Mode |
AUTO,
NORM, FIX, SINGLE |
| Trigger
coupling |
AC,
HFrej, DC, TV-FRAME, TV-LINE |
|
Trigger sensitivity |
| Trigger
coupling |
Synced range frequency
range |
Internal sensitivity (amplitude) |
External sensitivity
(amplitude) |
| |
|
NORM |
FIX |
NORM |
FIX |
| DC |
DC to 20MHz |
1div. |
1.5div. |
100mV |
150mV |
| |
20MHz to 50MHz |
1.5div. |
2div. |
150mV |
200mV |
| AC |
10Hz to 20MHz |
1div. |
1.5div. |
100mV |
150mV |
| |
20MHz to 50MHz |
1.5div. |
2div. |
150mV |
200mV |
| HFrej |
Minimum
triggering amplitude increases above 10kHz |
| TV |
TV-F, TV-L
Comp.video |
1.5div. |
1.5div. |
150mV |
150mV |
|
Calibration voltage |
1Vp-p±3%
(positive polarity, approx. 1kHz, square wave) |
|
Intensity modulation |
| Input
voltage |
TTL
level (＋5V) diminishes as positive polarity |
| Input
impedance |
Approx.
10kΩ |
| Frequency
range |
DC to
3.5MHz |
| Input
range |
100Vp-p
or 50V (DC＋AC Peak, 1kHz or under） |
| Output
voltage |
Approx.
50mVp-p/div |
| Output
impedance |
Approx.
50Ω |
| Frequency
response |
5mV to
5V/div. : 100Hz to 50MHz (－3dB)
1mV to 2mV/div. : 100Hz to 20MHz (－3dB) |
| Trace
rotation |
Enables
trace rotation adjustment by semi-fixed controller on the panel |
|
Storage section |
|
Vertical resolution |
8bit
(25dot/div.) |
|
Dynamic range |
±5div |
|
DC |
DC to
16MHz [8MHz] (sine interpolation) |
|
AC |
5Hz to
16 MHz [8MHz] (sine interpolation) |
|
Rise time |
Below
40ns [80ns] (With linear interpolation) |
|
Display memory (data) |
2KW/CH
(200dot/div) |
|
Display memory (REF) |
2KW/CH |
|
Acquisition memory |
4KW/CH |
|
REF memory |
2KW/CH |
|
Display memory (data) |
2KW/CH
(200dot/div.) |
|
Display memory (REF) |
2KW/CH |
|
Acquisition memory |
4KW/CH |
|
REF memory |
2KW/CH |
|
Memory backup |
Battery
backed up for approx. 30,000 hrs. (at normal temperature) |
|
Acquisition memory |
4KW/CH |
|
REF memory |
2KW/CH |
|
Sweep time・Display mode |
| NORM
sampling |
0.1µs/div. to 500s/div.（0.1µs/div. to 2µs [5µs]/div. in the MAG range)
(Maximum sampling rate : 40MS/s [20MS/s]) |
| Peak
detector |
10µs
[20µs]/div. to 500s/div. |
| Roll mode |
0.2s/div. to 500s/div. |
|
Storage mode |
| AUTO |
Same
operation as NORM for the same period, free-running data updating in other
cases. |
| NORM |
Data
updated each time an acceptable trigger is received. |
| SINGLE |
Data is
storaged with the first acceptable triggering after resetting and held |
| AVG
(Averaging) |
Average
of 4 or 16 or 64 times |
| SMT
(Smoothing) |
Data
writing point will be averaged following 32 words. |
| PST
(Persistence) |
Mutual
display of maximum and minimum values in storage, and initialization by
PST RESET. |
| PEAK |
25ns
glitch detection |
| ROLL |
NORM :
Continuous recording and updating of data on the CRT.
SINGLE : After receiving the acceptable trigger, the pre-triggering data
is updated and the data is stored. |
|
Magnification, Compression |
|
Magnification |
By
pressing X10 MAG under Hold conditions, 10-times magnification is obtained
by linear interpolation around the CRT center. |
|
Interpolation |
Linear
interpolation, sign interpolation |
|
Trigger・Delay |
|
Pre-trigger |
NORM : 0
to 20div. (in 2.5div steps)
ROLL-SINGLE : 10div. to 20div.(in 2.5div steps) |
| Usage of B
triggering |
AFT.DLY
: B STARTS AFTER DELAY TIME
B TRIG´D : B TRIG´D AFTER DELAY TIME |
| Effective
storage frequency range |
DC
to 16MHz [8MHz] (－3dB Adjustable sampling rate for the SWEEP TIME /DIV.) |
| External
clock |
Carries
out sampling by first transition of signals input from the external clock
terminal when setting SWEEP TIME/DIV to EXT. |
| Input
impedance |
1MΩ
±2%、Approx. 25pF |
| Maximum
input voltage |
100Vp-p
or 50V (DC＋AC peak, 1kHz or below） |
| Input
signal level |
TTL
"L" level＋0.4V or less
"H" level＋3.2V or more |
| Input
signal frequency range |
DC to
1MHz (1 kHz in roll mode) |
| Input
signal duty ratio |
20% to
80% (at "L" level＋0.4V, "H" level ＋3.2V) |
| Waveform
calculation |
＋, － |
|
PLOT OUT (Display hardcopy) |
| Output |
HP-GL
command, CRT display hardcopy (only data transfer) |
| Baud rate |
9600/1200 bps |
| Transfer
type |
data
length＝8bit, no parity
stop bit＝1bit or more |
|
Readout section |
| Display |
Capable
of ON/OFF by pressing and holding the CURSOR MODE switch for about 1
second. |
|
Calendar |
| Display |
Year /
month / day / hour / minute |
| Clock
accuracy |
±2minutes/month |
| Battery
life |
Approx.
30,000 hours (at room temperature) |
|
Setting values |
| Vertical
axis related items |
CH1, CH2
scale factors (with probe detector) V-UNCAL, ADD, INV |
| Horizontal
axis related items |
(A, B)
sweep scale factor (MAG conversion), ×10MAG, X-Y, external clock SWEEP
VARIABLE UNCAL |
|
Trigger-related items |
DELAY
TIME, B TRIG´ D |
| Storage
related items |
X-Y
sampling rate, display scroll, setting storage function (kind of PEAK, AVE
and count, SMT, PST, ROLL, kind of interpolation pre-trigger, point, REF
memory setting condition, menu, OUTPUT) |
|
Cursor measurement |
|
Cursor modes |
ΔV1,
ΔV2, ΔT, 1/ΔT, RATIO (V or H) PHASE (at VARI UNCAL) |
|
Measuring resolution |
10bit |
|
Measuring accuracy |
±4% |
|
Vertical direction |
±3.6
div. or more at center of CRT |
|
horizontal direction |
±4.6
div. or more at center of CRT |
|
Other |
| Case
dimensions |
305
(W)×150 (H)×400 (D) mm |
| Maximum
dimensions |
347(W)×165 (H)×459 (D) mm |
| Weight |
Approx.
9.6kg |
Temperature/humidity
for characteristics in spec. |
10°C
to 35°C, 85% or less
(without condensation) |
Temperature/humidity
for operation |
0°C to
40°C, 85% or less
(without condensation) |
|
Accessories |
| Probe |
PC-53
(2) |
| |
Power cable
(1)
Instruction manual (1)
Alignment tool (1) |
|
Options |
| OUT PUT |
Makes
possible mounting of optional IF-10 or IF-20 (but simultaneous mounting is
not possible). |
| IF-10 |
GP-IB
(complies with IEEE-488 1978) |
| Operation |
Outputs
screen numerical data and screen readout data through GP-IB interface
computer. (TALK ONLY, HP-GL command). Plot out the screen waveform and
screen readout data to the GP-IB interface plotter. |
| IF-20R |
EIA
RS-232C interface |
| Operation |
Prints
out screen waveform and screen readout data with an RS-232C printer (only
model DPU-412 made by Seiko Electronics, Ltd.). Outputs screen waveform
data and screen readout data to the RS-232C interface computer. |
| Baud rate |
9600/1200bps |
| Transfer
type |
Data
length＝8 bits without parity
Stop bit length＝1 bit or more
Delimiter＝CR＋LF
Handshake＝CTS-RTS system |
)
